Micro-Blaster: A compact and portable demolition system for rock breaking. Used by contractors, excavators, and other field workers to enable the efficient removal of boulders, concrete structures, and rock formations.

Keywords: bedrock busting, rock cracking, rock breaking, excavation, demolition tools, demolition equipment, construction technology, public works, trail building, cave rescue, rockhounds, ditch digging, concrete removal.
 

Micro-Blaster Accessories

Available from ezebreak

Gas Powered Rotary Hammer Drill


This compact Gas Powered Rotary Hammer Drill will allow users to drill rock and concrete in almost any environment (always use with proper ventilation in enclosed areas). Besides being highly effective at drilling holes in the drill/hammer mode the tool easily switches to rotary only or hammer only modes and also has a unique feature allowing users to rotate SDS shank chisels to a preferred angle before using in the hammer only mode. Packaged in a blow molded case which includes 3 SDS+ drill bits (6, 8, and 10 mm), SDS+ chisel and moil point, depth gauge, manual, service tools, and fuel mixing bottle. Highly recommended for back country projects especially where electric power is not easily available and lots of holes will be required. Absolutely the best gas powered SDS rotary-hammer drill currently in production!

Click here for Technical Data



Rotary Hammer Drills

Rotary hammer drills are the best tools for drilling holes required by Micro-Blaster System in both concrete as well as stone. Tools labeled "Hammer Drills" and having a 3 jaw chuck should be avoided as they will take many times longer to establish the required holes. Make sure the drill you intend to use takes a SDS+ shank drill bit and use only 5/16 inch diameter drill bits with your Micro-Blaster System.

Manufacturer: Hilti

TE 6-A: 36 VOLT BATTERY POWERED ROTARY HAMMER WITH UNMATCHED POWER RESERVES FOR COMPLETE MOBILITY

This is the ultimate battery powered rotary hammer drill currently on the market. Capable of drilling 10 plus 5/16" dia. x 12" deep holes per battery charge. Extremely well made and very dependable for use anywhere especially in remote locations. Highly recommended by ezebreak

Click here for Technical Data



TE 2, 115 Volt Rotary Hammer Drill

Super tough and dependable unit, this 115 volt rotary hammer drill can be used with generators, inverters (use units 1.5 times rated power input) and of course 115 volt outlets. Extension cords should be as short as practical to avoid voltage drop which can cause power loss and overheating.  If users own generators, this is the least expensive professional tool from Hilti for use with your Micro-Blaster system. Highly recommended by ezebreak

Click here for Technical Data

Manufacturer: CS Unitec

Air Rotary Hammer Drill — SDS Plus

This air powered Rotary Hammer Drill is the ultimate tool for drilling holes for the Micro-Blaster System, especially if you need to drill a lot of them. Unit includes SDS+ chuck for use with our 5/16" drill bits, variable throttle for 0-3000 blows per minute with an out put of .7 HP at 90 psi. Capable of drilling up to 1" dia. holes in concrete and manufactured in Germany to exacting specifications it is available in an UNDERWATER VERSION (Manufacturers #: 2 2404 0030, part#: 2 2404 0010 shown above for use out of water). Why are we selling an underwater version? Because we have an adapter kit in the works to allow the Micro-Blaster II system to be used under water at depths of 20 ft. Hopefully available by September '07


SDS+ DRILL BITS FOR MICRO-BLASTER I & II


Many of our customers have had problems finding the proper 5/16" dia. drill bits for their Micro-Blaster Systems. We now stock 2 models which will produce the required holes. The shorter of the 2 models shown above will drill up to 12" deep holes for double cartridge shots and is marked with a red stripe at 10" from the tip for single cartridge shots. The longer bit pictured has the capability of drilling up to 16" deep which will allow users the option of using 1, 2, 3, or up to 4 cartridges per shot. This bit also has a longer lasting carbide tip which should give excellent service in even the hardest materials.

Micro-Blaster II Air Tank


When charged with 120 psi of air will reliably trigger three Micro-Blaster II Heads. Easily recharged with Bicycle Tire Pumps Provides extreme portability for working in remote areas. Materials: Aluminum Tank, Brass Fittings Dimentions Overall: 10”Lx4.75”Dx5”H Max Pressure: 150 psi Capacity: 0.5 Gal. Weight: 2.5 lbs.

PowerBright™ 1100 WATT POWER INVERTER

This accessory allows the use of 115 VAC Rotary Hammer Drills in almost any location you can get your vehicle, including ATV's with 12 VDC systems. Easily attached to a vehicle battery with the included cable and clips or the inverter can be permanently mounted inside your vehicle (4 gauge cable recommended for permanent installation). Supplied with automatic overload protection, thermal protection, polarity protection and a switched voltage/wattage display, this unit's advanced features will insure years of trouble free service. Inverter comes complete with attachment cables, a spare set of fuses and manual. Warranty by manufacturer: 1 year against defects.

TIP: We recommend a minimum 14 gage grounded (3 prong) extension cord for runs up to 50 ft. For longer runs use a 12 gauge cord up to 100 ft. This unit will also power a small 115 VAC Compressor for recharging your air source in the field. Very handy when working in remote areas. Check label on compressor to determine max. power required and do not overload inverter.

Click here for Technical Data.


Micro-Blaster BLOW GUN ASSEMBLY


Other than drilling, the most tedious aspect to using your Micro-Blaster is the hole cleaning process. To speed up this operation we have developed the blow gun assembly seen above. Equipped with a 1/4" quick connect plug (Industrial Interchange, same as our manifold hose connector), a 5 ft. air hose, a lever valve and a 9.5" long, 1/4" dia. stainless tube, the unit will quickly and thoroughly clear the dust from drilled holes in just one or two seconds. Since its use is intermittent only a small compressor, capable of 100 psi output, is required for operation.

!!!SAFETY NOTICE!!! THIS BLOW GUN ASSEMBLY IS NOT OSHA COMPLIANT AS IT DOES NOT LIMIT PRESSURE AT THE NOZZLE TO 30 PSI CARE SHOULD BE USED NOT TO DIRECT OUTPUT AT PERSONNEL. ALWAYS WEAR APPROVED EYE PROTECTION WHEN USING THIS AND OTHER EZEBREAK PRODUCTS WORK SAFELY AND CRACK WISELY!


Air Tank Conversion Kit


If you already have your own air tank you may need components to connect the Micro-Blaster to your tank. For your convenience we have put together a kit containing the above components.   Ask your Dealer or Ezebreak for the Air Tank Conversion Kit (Part# MBIIx3-ATCK) if you cannot easily find these components locally. Click here for detailed instructions and tips.
 
Products